Ford axle identification.

Ford Rear Axle Assembly Identification - Page 01 - FORDification.com "WFY-A5" - Ford Pass 1977, Lincoln and Towncar 1972, Lincoln and Towncar 1974-79. 2.75 gear ratio, 28 spline axles and the 4 pinion (spider gear) Equa-lock rather than the lesser 2 pinion Traction-LocTo determine which one you have, check the number of splines your axle has. If it has 30 splines or less, then it's a Dana 60 axle. If there are 33 or 35 splines, then you have a Dana 70 axle. If you have a 1994-2001 Dodge you may have a Dana 80 axle which also has 35 spline axle shafts. There are three variations of the Dana 60 axle.The axle code 15 in a Ford Expedition refers to a 3.73 non-limited slip axle ratio. The axle code 15 indicates that the Expedition is equipped with a rear axle ratio of 3.73 and does not have a limited slip differential. This axle ratio is ideal for towing and hauling heavy loads, providing better torque and power for these tasks.They were the 450s of the OBS, 2wd with a leaf spring mono beam axle on the front like a semi. Straight narrow frame with a 10 lug Dana 80 with disc brakes & hydro boost. Geared to the moon, they came with 4x4 E4OD or ZF5 trannys & had a parking brake that bolted onto the rear of the tranny inside of in the axle itself.Sep 16, 2021 ... The Ford Mechanic will know what to do about your part. Do you have any other details that could be helpful? If so can you provide part numbers.

The quickest way to tell which axle your Bronco has is to look at the top of the steering knuckles where the Front End Housing is connected to the Knuckle. On a Dana 44, you will see a large castle nut threaded onto a ball joint. On a Dana 30, you will see a king pin cap with four bolts threaded down into the top of the knuckle.1994 Ford Mustang Axle Information & Ratios. Your Mustang will be equipped with a Vehicle certification label on the driver’s side door jam. This label will show your axle code under the “AX” slot. ... Axle identification: Ratio and Type: 8: 2.73 Axle Ratio – Conventional: M: 2.73 Axle Ratio – Limited slip: 7: 3.07 Axle Ratio ...The Ford 9.75" Rear End The 9.75" rear end is the old war horse of the two available rear ends for the 2015-2020 F150s. The good news is that the 9.75" is extremely distinct in how it looks, and in our experience, is the more common of the two differential options.The 9.75" has a very noticeable taper the goes toward the passenger's side of …

1973 - 1979 F-100 & Larger F-Series Trucks - Dana 60 and Dana 70 Axle ID Help - I just picked up a Dana 70 dual wheel rear end (4.56 gears) and also a Dana 60 single wheel rear end (4.10 gears) and I'm trying to identify what vehicle (and year) these came out of. ... I've only messed with Ford 8" and 9" third members, where they are removable ...Driver license and ID, renewals, and replacements. You can renew your Texas driver license or ID card: Online. Over the phone. In-person at a Department of Public Safety office. By mail. Each renewal method has different eligibility requirements. Learn which renewal method is right for you.

and you cant put 31 spline axles in a 28 spline housing. bearings sizes are different. 79-93 is one length, 94-98 is one length and 99-04. All explorers and trucks with an 8.8 had a 31 spline trac lock. There was no such thing as an 8.8 until 1983. Not all F150's and Explorers have Trac-Lok, as it's an option.In conclusion, decoding Ford axle tag codes is essential for identifying the specific details of the axle installed in a Ford vehicle. Understanding the axle ratio, differential type, ring gear size, manufacturing plant, and date of manufacture allows owners and mechanics to make informed decisions regarding repairs, upgrades, and vehicle ...Step 1 - Locate the Axle Code. To find the axle code: 1. View the Safety Compliance Certification Label on the driver's side, front or rear door panel. 2. Find the word "AXLE" …1973 - 1979 F-100 & Larger F-Series Trucks - Axle Identification - Hi, I have a '78 F-150, 4 x 2, was a 351 M now a 460. The rear axle is coded 15 J on the door. On the axle it says 3.25. What I need to know is it a 31 spline or is it a 28 spline axle? I am looking to buy a 3.50 locker rear axle and I am going to look...

(mk2 cortina dampers mount in front of the axle casing on both sides). also, the handbrake cable pulley is used on the mk1 capri (although mk2 cortina used a similar system but that depended on whether a floor mounted or dash mounted handbrake was used). mk1 capri had anti-tramp bars, ford always fitted them above the axle. guess the bushes ...

How electrocardiogram (ECG) tests can identify conduction disorders in the heart and cardiovascular system. Clinical resource. Try our Symptom Checker Got any other symptoms? Try o...

2009 - 2014 Ford F150 - Axle tag id ON AXLE ITS SELF!!! - so, my local pull it yourself LKQ got a bit of a unicorn middle of last month they got a 2013 F-150 ext cab hit hard in the front. First time I have seen our body style at that yard. The engine and trans were already taken. it is a VERY low miles truck I got...axle identification. I think I answered my own question. I did a search over on the ford-diesel.com site and found a lot of info. I seems the tag on the axle has either a 229 or 248 and the 229 is a D50 and the 248 is a D60. I have the 248 or D60 axle. I …CrownVic.net is a forum and information center dedicated to the Ford Crown Victoria and its siblings: Mercury Grand Marquis, ...1987 - 1996 F150 & Larger F-Series Trucks - Axle ratio identification help - I have a 1989 F150 4x4. I am unsure of my axle ratio's and with good reason. The door code says 18, which I know is 3.08 Non-LS. The guy I bought the truck from told me that he replaced the rear axle with a different ratio.Dec 13, 2023 · Decoding Ford rear axle codes can be a bit complex, but by following a step-by-step process, it becomes much easier. Each letter and number in the rear axle code has a specific meaning, allowing you to extract valuable information about your axle. For example, the first two letters of the code indicate the axle’s size and capacity, while the ... Recent dropped axles are rated in total drop, early axles on amount of drop over original Ford. Dimensions between holes are ceter to center from top of axle. Kingpins perches perch thickness. 1928-31 51 7/8 36 1/4 2 1/4 (continuous curve across) 1932-36 51 3/4 36 3/8 2 (ends curve more) 1937-41 50 7/8 38 1/2 2 1/4.Identifying Your Rear Axle Flange. Ford, Chevrolet, Oldsmobile, Pontiac, they all used a different axle flange at one point or another. Being able to identify the flange you have can spare you a lot of grief when it comes time to buy parts, not to mention speeding up the process as a whole. Check out the graphic below to help you identify some ...

AXLE 37J: 37 = Dana 60 / 3.54-1 / No Limited Slip // J = Power Steering. IF the AXLE code stamped on the Warranty Plate begins with a letter: Limited Slip. If with a number, no Limited Slip. 1973 - 1979 F-100 & Larger F-Series Trucks - Axle Identification help and LSD Info - Finally able to get to work on my new 78'!Re: Rear Axle Identification. The right side (passenger) is of the '15 era - no reinforcing ribs on the backing plate, the left side (driver) would be in the '17 - '25 vintage. Closed driveshaft bearing spool is in the '10 - '20 era. There are subtle differences in the spool but I'm generalizing.In most cases, the short axle goes in the driver's/left side. In the above video, you'll see us installing the axle, then measuring out to the end of the bearing. You can also stick a tape measure into the axle tube and measure to the stop in the differential. As we measured, we did not account for the thickness of the backing plate.It's where I found the picture. He has some excerpts from the 1981 manual, which would be the same as your 80. 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks - Rear axle id - Hi I'm trying to identify a rear axle in my 1980 f250 I have the door code B5 and tag from the rear 3 33 EOTA UD 603943-5 L S i have tried using Dana's ...Re: Axle identification. I think the internals are the same. The difference is the external appearance of the pigs head because it has the mounting points for the trailing arms on the top. And the tubes will have different mounts for the coil spring platforms too.Quick ID guide for the Ford 8 in. and 9 inch rear axle. We look at how to determine Equa lok, traction lok and open differentials. We show the best and worst...

In 1977.5 Ford’s new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977. The F-250 is a little wider than the F-100 & F-150, for the wider 8 bolt wheel pattern.

Table of axle codes for the Ford F-150. In the table below you can see a selection of two-character codes, simply read across to the left to find your axle ratio – 3.31, 3,55 3.73, 4.10 and 9.61 for the lightning. You can see that codes that are purely numeric (e.g. “19“) correspond to a Non-limited slip, and codes with a letter (e.g. “L6“) correspond …Ford Rear Axle Assembly Identification - Page 17: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V106A: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106B: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106C: Ford …1932-1934 the wishbones are bolted to the bottom of the axle housings about 8" from the ends. the tabs for the wishbones are welded on, but will not go all the way around the housing, just the bottom. the spring hangers are forged on to the axle tubes. on the 1932, the part where the torque tube bolts to the diff is round (most) it is more of a ...Ford Rear Axle Assembly Identification - Page 11: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S157B: Ford F250SD, F350SD Pickup ‘99: 4.10: 10.50: L--S157C: Excursion '00 Ford F250SD, F350SD Pickup ‘99-01: …It has a 440/727, 14 bolt FF rear, and possibly a dana 60 front (closed knuckle). It still has the original dana 24 transfer case. So the front axle has that reads 4.09 D4TA SA BOM is 603480-1. Column left, 19th entry: Dana 44-6EFGH / 4.09-1 / No Free Running Hubs or Limited Slip / 3,500 lbs. Front Axle Capacity.Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle Identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines.Find the word "AXLE" under the bar code. 3. Find the two-digit code under "AXLE." Step 2 - Find the Axle Ratio. To locate the axle ratio after you have found the axle code: Visit the RV & Trailer Towing Guides page on the Ford Fleet website. Select the Towing Guide for your vehicle's model year. Note: Rear axle ratios are available for 2008 and ...Ford Rear Axle Assembly Identification - Page 08: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WFG-A: Ford Pass., Mercury '70-74: 2.75: 9 in: L: 28-WFG-A: Ford Pass., Mercury 70-74:Ford Rear Axle Assembly Identification - Page 07: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. '82-'83: 3.42: 8.5: L: 28-WFC-G: Capri, Mustang, Cougar 82 Fairmont, Zephyr, Granada 82 Lincoln Continental '82 Thunderbird 82: 3.08: 7.5: L: 28-

Call our staff of experts at 888-382-2953. We're here to help Monday thru Friday from 8AM to 5PM CDT. GM Vehicles come with a RPO code tag, usually located in the vehicles glovebox or door jamb. These tags have a wealth of information about your specific vehicle's equipment and specifications. Read more about GM RPO Axle Identification Codes.

The trick is to identify the weak from the strong, the common from the obscure. This guide will help you decide which axle is best for your needs and whether the one currently under your ride will ...

Housing Identification. 57 - no dimples, flat center band up the center of the rear cover, bottom drain plug. 58-59 - two dimples on back of housing, flat center band, some had drain holes. 60-67 - two dimples, flat center band, oil level hole in back cover. 63-77 Lincoln, LTD, Thunderbirds had 9.375 inch centers, housings were cut away at the ...The Ford 9.75" Rear End The 9.75" rear end is the old war horse of the two available rear ends for the 2015-2020 F150s. The good news is that the 9.75" is extremely distinct in how it looks, and in our experience, is the more common of the two differential options.The 9.75" has a very noticeable taper the goes toward the passenger's side of …The axle code can typically be found on the vehicle’s door tag, which is located on the driver’s side door jamb. It may also be stamped on the axle housing itself …The numbers can also tell you what car the rearend came in, though you need to look up the info online or in a Ford manual, as there are thousands of codes.The Mustang II utilizes two different style rear axles. The first axle is used on 4cyl and some 6cyl cars and is a 6 3/4" ring gear integral carrier axle. The second is used on some 6cyl and all 8cyl cars and is an 8" ring gear removable carrier axle. The two axles are easy to tell apart. Looking at the axle from the rear of the car, if the ...1 / 1. Forum Jump. 1987 - 1996 F150 & Larger F-Series Trucks - Dana 60 Front Axle Identification - I bought a Dana 60 it is supposed to out of an 89' F-350, so it has kingpins and the like, the axle ratio tag has the 610255 code on it, saying it is a 1986-88 Dana 60 kingpin axle. however the axle is not stamped 60 where it should,...The solid axle in a F-150 is also a "live" axle, because it transmits power to the wheels. A solid axle is comprised of: Axle tubes welded to a differential housing. Differential cover. Axle shafts that run inside the axle tubes. Differential gears that transmit power from the driveshaft to the axleshafts. Wheel bearings in the outer end of the ...Another sopt is a white sticker located in the doorjamb there is either a number or letter under axle. Conventional or "open" rear ends break down as follows: 8-2.73, Y-3.08, 5-3.27, F-3.45, 6-3.73. ... Mustang Club of America #82740, White Mustang Registry #362, NMRA, Fun Ford Weekend, Mustangs of Burlington M O OG Certified Technician For ...There is two different nuts for the early Ford spindles. 1928-35 Have a larger (taller) nut. In 1936, Ford went to a shorter castle nut. All threads are the same (3/4-16) Early Ford spindle identification & information including details from the 1920's, 1930's & 1940's. Specifications and sizes to educate about early Fords.

Ford Rear Axle Assembly Identification - Page 15: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S832E: Bronco '94-95 Ford F150 Pickup '94-96: 3.31: 8.8: NL--S832F: Bronco '94-95 Ford F150 Pickup '94-96: 3.31: …Ford Rear End Catalog: Hot to Select Axle & Measure the Companion Flange: Your Source for Classic / Late Model Auto Parts: INFO 404-767-3378 FAX 404-305-9437: CONTACT METRO: ... How to tell whether yours has a 28 or 31 spline axle. This method works for pre-1971 axles, after that a few 31 splines were produced with the concave oval in the ...If you own a Ford tractor and want to give it a fresh new look, finding and applying the right decals can make a world of difference. Ford tractor decals are not only a great way t...Instagram:https://instagram. kdka tv reporterslexus gs years to avoidannapolis md tide chartjewelry stores corinth ms Identifying Your Rear Axle Flange. Ford, Chevrolet, Oldsmobile, Pontiac, they all used a different axle flange at one point or another. Being able to identify the flange you have can spare you a lot of grief when it comes time to buy parts, not to mention speeding up the process as a whole. Check out the graphic below to help you identify … 1980-1996 Ford F-250 Dana 44IFS Front Axle Identification IDN-136 $0.00 Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s. peter caride md21 naughty wedding pictures Ford Front Axle ID. Refer to our Ford axle identification charts to quickly Identify the parts and information you need. Each of our Dana 44 and Dana 60 front axle identification … labcorp copper Ford front end, found in both straight axle and independent front suspensions. Often confused with a Dana Spicer 60. Please check your bill of material numbers for proper identification. Used in Models: F250: 1980 - 2004 (Front) F350: 1980 - 1986 (Front) Dana Spicer D60. 10 bolt cover with 9.75" ring gear.Depending on the model, you can typically find it on the driver’s side door jamb, the glove compartment, or in the owner’s manual. Additionally, there are online resources that provide comprehensive lists of axle codes for various Ford models to help you identify the specific code for your vehicle. differential ford axle code chart.External Identification Characteristics of Ford Dana 50 Twin Traction Beam Independent Front Suspension Front Axles: Leaf Spring Suspension; Left and Right Axle Beams formed from stamped and welded steel; Outer End of 8 Bolt, Internally Splined Wheel Hub is approximately 4-3/16" in diameter; Axle Shaft Universal Joints have External Snap Rings